Hi-Chrome Iron Castings – ASTM A-532-19

High-Chromium White Iron for Severe Abrasion Applications

Pacific Alloy Casting Company manufactures Hi-Chrome (high-chromium) white iron castings in accordance with ASTM A532-19. Hi-Chrome iron is engineered to deliver exceptional resistance to abrasive wear in demanding industrial environments.

Pacific Alloy Casting Company produces Hi-Chrome iron castings using controlled foundry practices that focus on:

Castings are manufactured to customer specifications and application requirements.

Pacific Alloy Casting Co. office building entrance
What Is Hi-Chrome Iron?

Hi-Chrome iron is a white cast iron alloyed with elevated levels of chromium to form hard chromium carbides within the iron matrix. This carbide-rich microstructure provides:

Hi-Chrome iron is also commonly referred to as Chrome Carbide iron.

Hi-Chrome Iron vs. Other Abrasion-Resistant Irons

Hi-Chrome iron is commonly evaluated alongside:

Selection depends on factors such as impact loading, abrasion severity, operating conditions, and desired service life.

When compared to nickel-alloyed white irons, Hi-Chrome iron is often selected when additional abrasion resistance or toughness is required.

Performance Characteristics of ASTM A532-19 Hi-Chrome Iron

Castings produced to ASTM A532-19 offer:

When compared to nickel-alloyed white irons, Hi-Chrome iron is often selected when additional abrasion resistance or toughness is required.

Molds and castings on the foundry floor
Abrasion-Resistant Cast Iron · 12% Chromium White Iron (Class II, Type B)
PropertyDetail
Common Name / Type12% Cr white cast iron; Class II Type B chromium-molybdenum white iron
Material ClassHigh-chromium white iron (abrasion-resistant)
Key CompositionC 2.4–3.6%, Cr 11.0–14.0%, Mo up to 3.0%, Mn up to 2.0%, Ni up to 2.5%, Si up to 1.5%
MicrostructureM₇C₃ chromium carbides in a martensitic / austenitic matrix (matrix adjustable by heat treatment)
Hardness — As-Cast~ 450–550 BHN
Hardness — Hardened (heat-treated)~ 600–650 BHN (up to ~ 60+ HRC)
Tensile StrengthLow / not a design parameter — material is consumed in compression and abrasion, not tension
Toughness / DuctilityLow; brittle — moderate impact resistance for a white iron but far below steels or ductile iron
Standout PropertyExcellent abrasion resistance with better fracture toughness than higher-carbide grades, thanks to the discrete (rather than continuous) carbide structure
Heat TreatabilityYes — can be hardened and tempered; matrix can be tuned (austenitic-as-cast for toughness, or hardened for max wear). A key advantage over Ni-Hard grades.
MachinabilityPoor. Hard carbides make conventional machining impractical — typically ground or finished with CBN/diamond tooling. Best practice is to machine in the soft/annealed condition (if used) before final hardening, or design for grinding only.
WeldabilityPoor / not recommended. High crack sensitivity from hard, brittle structure. If repair welding is unavoidable, use high-preheat and specialized high-alloy electrodes; structural welding should be avoided.
Corrosion / Oxidation ResistanceModerate — the elevated chromium gives better mild-corrosion and oxidation resistance than low-Cr (Ni-Hard) white irons, though well below stainless or 25% Cr grades.
Relative CostModerate — higher than gray iron, generally lower than the 25% Cr (Grade III) irons.
Section-Size SensitivityModerate — heavier sections cool slower and may need controlled heat treatment to achieve target hardness throughout.
Best-Fit ApplicationsMining and mineral processing wear parts, grinding mill liners and components, slurry pump parts, classifier shoes and wear plates, crusher components, and high-stress abrasion environments where some impact loading is present.
Not Recommended ForTensile/structural load-bearing parts, weld-fabricated assemblies, high-impact shock loading, or parts requiring extensive post-cast machining.
Abrasion-Resistant Cast Iron · 25% Chromium White Iron (Class III, Type A)
PropertyDetail
Common Name / Type25% Cr white cast iron; Class III Type A high-chromium white iron
Material ClassHigh-chromium white iron (abrasion- and corrosion-resistant)
Key CompositionC 2.0–3.3%, Cr 23.0–28.0%, Mo up to 1.5%, Mn up to 2.0%, Ni up to 2.0%, Si up to 1.5%
MicrostructureM₇C₃ chromium carbides in an austenitic or martensitic matrix; higher Cr content shifts more chromium into the matrix for corrosion resistance
Hardness — As-Cast~ 450–550 BHN
Hardness — Hardened (heat-treated)~ 550–600+ BHN (up to ~ 60 HRC)
Tensile StrengthLow / not a design parameter — used in compression and abrasion, not tension
Toughness / DuctilityLow; brittle — comparable to other white irons, with toughness tunable somewhat via matrix heat treatment
Standout PropertyCombines high abrasion resistance with notably better corrosion and oxidation resistance than lower-Cr white irons — the defining advantage of the 25% Cr grade
Heat TreatabilityYes — can be hardened and tempered; matrix can be set austenitic (as-cast, tougher) or hardened to martensite for maximum wear resistance
MachinabilityPoor. Hard carbides require grinding or CBN/diamond tooling; machine in soft/annealed condition before final hardening where possible, otherwise design for grinding only
WeldabilityPoor / not recommended. High crack sensitivity; if repair welding is unavoidable use high preheat and matched high-alloy electrodes. Avoid structural welding.
Corrosion / Oxidation ResistanceGood (best of the A532 family) — the high chromium provides meaningful resistance to corrosive slurries, acidic conditions, and elevated-temperature oxidation
Relative CostHigher — the richest-alloy grade in the A532 family, generally the most expensive of the white irons here
Section-Size SensitivityModerate — heavier sections may need controlled heat treatment to develop uniform hardness through the cross-section
Best-Fit ApplicationsCorrosive and abrasive slurry pumps, brick and ceramic dies, mining and mineral processing wear parts, flue-gas and FGD components, pump volutes and impellers handling aggressive media, and high-temperature abrasive environments
Not Recommended ForTensile/structural load-bearing parts, weld-fabricated assemblies, high-impact shock loading, or parts requiring extensive post-cast machining
Typical Applications for Hi-Chrome Iron Castings

Pacific Alloy manufactures Hi-Chrome iron components used in industries and applications such as:

These applications rely on materials that can withstand continuous abrasive contact while maintaining dimensional integrity.

Mineral processing plant at dusk

Contact

Discuss Your Hi-Chrome Iron Casting Requirements

If you’re evaluating Hi-Chrome iron for a specific application and need guidance on grade selection or production capability, Pacific Alloy is ready to help.

Discuss Your Casting Requirements

📞 562-928-1387

✉️ sales@pacificalloy.com

Early-stage discussions welcome. NDAs available.